Sunday, February 17, 2019

"X" could be the ultimate sleeper...

Kiss had a hit several years ago titled "Let's Put the "X" in Sex".  I thought of that and thought about an often neglected car that has great potential-The 1968-79 GM "X" body. The '68-74 Chevy Nova already has kind of a "cult" following-you see tons of them in the buff magazines. However almost all of those are done in the '90's "Pro Street" style-i.e.-looking like Pro Stock drag racer-narrowed rear ends with huge tires in the rear, a nasty small or big block Chevy with a blower or tunnel ram protruding through the hood. And that's Ok. My vision is a little different. "X" bodies have great potential for two reasons. # 1. Their engine bays will swallow anything from a Chevy straight six, a Buick V6, a 350 Chevy, Pontiac, Olds or Buick to a 454 Chevy or a 455 Pontiac or Olds or Buick. # 2. The basic platform is the same as a Camaro or Firebird. That means any suspension or brake upgrades that fit a Camaro / Firebird will fit these cars. You could build a drag racer that will pull the front wheels on take-off, a corner carver that can run with a Z06 'Vette in the twisties, or anything in-between. The first word of advice I would give any X-Body builder is first off-get the one you want. Chevy Novas are the most popular and will be pricier than the other versions, but compared to a same-year Camaro or Chevelle their still dirt cheap. If you want a Pontiac Ventura, get one. Ditto for an Olds Omega. Not many Buick Apollos around, but there's a few. Secondly try to get one with the engine line you want. Because of GM playing musical engines in the '70's because of smog laws a lot of these are going to have small-block Chevys in them, which is if anything a plus factor. There's more speed equipment for a small block Chevy than anything else on the planet. Even if it has anemic 262 or 305 that's not a deal breaker because a 350 or 383 stroker would be a bolt-in. However-if you "gotta have" a "real" Pontiac engine in your Ventura-their are a lot of them with 350 Pontiacs under the hood. The good thing about this is 350 Pontiacs respond well to basic hot rod tricks-carb and intake, headers and dual exhausts, mild cam, etc. You can make 325-350 hp and 400 lbs ft of torque pretty easy. If you need more than that-a 400 or 455 is a bolt-in swap. Their are Omegas out there with 350 Olds V8s under the bonnet. Of the "other"-i.e.-non-Chevrolet 350s the Olds has the most potential. Edelbrock claims 397 hp and 400 lbs of torque from their "Performer RPM" package on a 350 with stock heads. 400 hp will turn a 3,200 lb "X" body into an absolute rocket. If you want more than that-a 403 would be a bolt-in swap-53 extra cubes will give you a big torque boost. You'd need special pistons-but you can use 455 heads on a 350 / 403 if you want to build a real stomper. Or you could swap in a 455. As for Buicks-if you find one with a 350 Buick they make nice drivers-but their isn't much speed equipment available for 350 Buicks. There is quite a bit for 400-430-455s-Edelbrock makes heads and intakes, Crane, Lunati, etc make cams, Hooker makes headers. If you find a 231 V6 model here's a thought-though it might be a little pricey. Find a wrecked late '90's early 2000's Buick Riviera or Pontiac Bonneville or Grand Am / Gran Prix SSEI with the Supercharged 3.8 V6. They have 240 hp stock, and could easily make 100-150 more by changing pulleys on the blower. Scarcer still and more expensive would be the vaunted Turbo V6 out a wrecked Grand National or Regal T-Type. Dynamite if you could find one. My personal choice would be a '71-74 Ventura.  As for suspension I would use WS6 Trans-Am sway bars and KYB shocks. I'd use an '84-92 WS6 Trans-Am steering box. These have a 12.7:1 ratio which is even quicker than the '70's T/A's 14:1. Some Year One 17X9 "Snowflake" or "Honeycomb" wheels shod with 255/ 50ZR17 tires. I'd use a 400 Pontiac stroked to 467 inches with aluminum Edelbrock heads. Besides the hp boost, the reduced weight on the front end will help handling too. I'd radius and flare the wheel wells to clear the big tires, and put front and rear spoilers on it. I'd cut a hole in the hood and use a Trans-Am "Shaker" scoop-like a '74 GTO. Paint would be either Monochromatic Sinister black, or Diamond White pearl with Diamond Blue pearl stripes like a '70-'72 Trans-Am or maybe a '78-79 "Macho" T/A. Any body else have ideas for a badass "X" body?  Mastermind    

Friday, February 8, 2019

"Brand Loyalty" and hating the others is just counter-productive....

I get so tired of seeing jacked-up Dodge Ram pickups with a sticker of "Calvin" ( of the comic strip "Calvin&Hobbes ) pissing on a Chevy Bow-Tie or Ford emblem. I'm really tired of 50 year old men acting like their 12 at car shows. "Chevys suck!" "Mopars Rule" "Fords Suck" etc, etc. Get over yourselves guys. Like it or not the Small-block Chevy is THE engine of the 20th century and is still relevant today. You can buy mega-hp crate engines for very reasonable prices. Introduced in 1955 It quickly eclipsed the flathead Ford that had ruled the 40's and 50's as "The" hot rod engine. Vic Edelbrock Sr. got started in 1938 by making hot rod parts for Flathead Fords. However, if that's all he ever did he'd have eventually went out of business and the company wouldn't be the Juggernaut it is today. Vic Sr and Vic Jr, visionaries that they were,introduced new products and changed with the times. Now 75 years later they are a power in the automotive aftermarket industry. However if when Bob Joehnk approached Vic Jr about making a high-performance manifold for the Small-block Chevy-instead of doing it and marketing it-if he had sneered "My dad built this business on Flathead Ford parts, that's our specialty." "And I hate those goddamn Chevys". His business would have went down the tubes. Get an increasing share of a shrinking market. Sure-fire way to bankruptcy. Thank god he was smarter than that. Years ago I worked in an Import Performance Specialty store. We sold high-performance parts for VW's, Porsches, MGs, Triumphs, Jaguars, and Datsuns amd Toyotas. Headers, cams, Weber Carbs, stroker kits, cylinder had we had it all. I loved the job and I enjoyed talking to our customers and helping them build their cars. I had one guy that ran a "Mini-Stock" a Toyota Corolla in dirt track races. It had a 2TC overhead cam 1600cc engine. It had a Weber carb and a header and a hot cam in it. For a little car it was really fast. And he won a lot of races with it. Another guy did road races with a Datsun 510.  Other guys hot rodded VW's-one guy had a wicked Karmann Ghia that suprprised many musclecar owners. Then there was the British enthusiasts with the Triumph Spitfires and TR6's, MGBs and Midgets. And these guys hated each other. The brits would walk barefoot over hot coals rather than drive a "rice rocket". The Japanese enthusiasts would deride the VW owners, the Porsche owners would deride them all. It was hilarious. Sometimes we'd damn near have fistfights in the lobby as these guys hurled insults at what a piece of shit the other guy's car was. In reality they were all nice cars that people had put a lot of time and money into. They should have got together and formed a big racing club and let people see who was better on the track. Instead there was the British clubs, the German clubs, the asian clubs. And they'd never co-operate, even if someone did suggest a big "Show-n-Shine" or "Track day".  Sad. However-musclecar guys act the same way. Although I've owned just about everything-I even briefly had a 302 Maverick "Grabber"-I'm a Pontiac Guy. I can't remember the number of times I've left a speed shop and been walking to my GTO or T/A or Ventura or Gran Prix, or whatever Pontiac I owned at the time and some asshole has to yell at me "Get a ( fill in the make-"Mopar, Chevy, Ford, Olds, AMC" ) . To which my response is always "Why would I want to Downgrade and drive a piece of shit like that?"  That usually shuts them right up. I must admit-that if this provokes further belligerence, I'm happy to go there too. I fought Golden Gloves in college and even turned pro for a while. Call me immature, but if some 40 year old adolescent wants his ass kicked because he said my car sucked and I said his sucked worse then I'll be happy to oblige. And that's a sad state of affairs. We all ought to appreciate a nice car regardless of make or model. So next time you see a hated Ford or Chevy or whatever that's done really nice, grit your teeth and politely say "Nice Car." If we all do that maybe the world will be a little nicer place.  Mastermind    

Wednesday, February 6, 2019

Consider all the facts before you deem something "GOAT" ..

I get really tired of sportswriters and car writers over-using the acronym "GOAT"- Greatest of all time."  There are very few people or things-( cars, motorcycles, etc)  that can be truly labeled the greatest in their own time, but all time?  No. The loudest coming from New England Patriots fans. On one hand I agree-Bill Bellicheck has done a spectacular job in his tenure there. Six Super bowl wins and ten appearances in 19 years-that's awesome. And he's done it with a revolving door of players in the free agent era. And certainly Tom Brady deserves a ton of credit. However-think of this-when Peyton Manning was in his prime with the Colts-and got hurt-the Colts went 4-12 that year. The year Brady blew his knee out-the Patriots went 11-5. That's coaching. However-People forget that Tom Landry took the Cowboys to the playoffs 16 out of 17 years from 1966-83, and played in 10 NFC Championship Games, and 5 super bowls, with two wins. Vince Lombardi's Packers won 5 NFL championships in 8 years, including the first two Super Bowls. Lombardi's Packers also won the 1965 NFL Championship-making them the only team to ever "Threepeat". Win-3 consecutive championships. Should Lombardi's accomplishment be discounted-simply because the game wasn't always called "Super Bowl?" Chuck Noll won 4 Super Bowls in 6 years with the Steelers and took them to the playoffs almost every year from 1972-1989. Don Shula won NFL Championships with the Colts,then took the Dolphins-and expansion team-and had them in the Super Bowl in just 3 years. They went 3 years in a row-"71,72, and '73-winning the last two. You think Bellicheck is good for going 11-5 without Brady?  In 1972-the unequaled, unbeaten season-The Dolphins star QB-Bob Griese broke his leg in the first game of the regular season. So the Dolphins went 17-0 with their backup QB-Earl Morrall. The Dolphins went to a couple more Super Bowls in the '80's losing to the Redskins and 49ers, and made the playoffs almost every year until Shula's retirement in 1995. As for Brady-yes he definitely is the best in the modern era. But if you look at the QB nowadays you get a 15 yard roughing the passer penalty. I'd like to see Brady take some of the hits that Terry Bradshaw took-Super Bowl 10-the winning TD pass to Swann?  The Hate Crime with Jerry Shirk that still makes people cringe today?? Or the hits that Roger Staubach, Joe Namath, Ken Stabler, Len Dawson and Jim Plunkett took on a daily basis with no flags thrown. Ditto for Randy Moss and Chad Johnson and Jerry Rice and all these Diva Recievers. I'd like to see what these candy-asses could do when you could hit them all the way down the field, not just the first five yards!  And conversely-How awesome would Lance Alworth, Bob Hayes,Paul Warfield, Drew Pearson and Lynn Swann have been if you couldn't touch them without a flag after 5 yards?  Now Patriot fans are going to sneer "6 Super Rings" No Debate."  If Super Bowl rings are the only measurement were using then yes there's no argument. But what about level of competition? Who they beat in the playoffs to get there? And who they beat once there? Let's compare the '70's Steelers to the modern Pats.  Are you going to say with a straight face, that this years Chargers were better than the 1978 Houston Oilers that had an awesome defense that rivaled Pittsburgh's Steel Curtain, the leading rusher and arguably one of the greatest running backs ever-Earl Campbell, and Dan Pastorini at QB and Mike Renfro and Kenny Burroghs as recievers?  Can you say that with a straight face?  Your going to say that this years Chiefs are better than the 1974 Oakland Raiders that had Ken Stabler, Cliff Branch, Fred Biletikoff, Mike Siani, Clarence Davis, Gene Upshaw and Art Shell, and a stingy defense that had killers like Jack Tatum and Willie Brown and Phil Villipiano?  The team that ruined the Dolphins run to four straight Super Bowl appearances in the "Sea of hands" divisional game?  Are you going to say that last year's Eagles were better than the 1978 Cowboys that had Roger Staubach, Tony Dorsett, Drew Pearson, Tony Hill,Preston Pearson, and the "Doomsday Defense?"  This year's game with the Rams was a defensive struggle? How about Super Bowl IX?  It was 2-0 at halftime. The Steelers eventually won 16-6, beating a tough Vikings team that had Carl Eller, Jim Marshall and Alan Page on the defensive line, Fran Tarkenton at QB, Chuck Foreman and Ed Marinaro for running backs and John Gilliam at Reciver. You think this year's Ram's were tougher than the 1974 Vikings? The '74 Vikings didn't have losing games that went 54-51 or 43-40!!  The same for Boxers. Yes Floyd Mayweather is great. But could he have beaten Sugar Ray Leonard in his prime? Or Roberto Duran, or Thomas Hearns, or Alexis Arguello, or Aaron Pryor or Hector "Macho" Camacho?  On any given sunday-maybe one of them. But two or more?  Uh-Uh. Tyson Fury, the Klitschko brothers, even Evander Holyfield and Lennox Lewis and Mike Tyson, non of the modern heavyweights would have even been contenders if they fought in the same era as Ali, George Foreman ( Foreman gave Holyfield hell and damn near took his title at age 42; at 27 he'd have destroyed him like he did everyone else ) Ken Norton, Joe Frazier, Earnie Shavers, Larry Holmes, Ron Lyle, Floyd Patterson, Oscar Bonavena, Bob Foster. And just like the rules changed in football-they didn't stop fights back then like they do now. You hung in there till you were down or your trainer threw in the towel. Travis Pastrano is going to break Evel Knieval's records? I'd like to see him do it on heavy Harley XR-750 instead of his 250 lb Motorcross bike!!  What does all this have to do with Musclecars?  I was talking to a guy the other day and I said if I ever built another project it was going to be a corner-carving '70's T/A with a snarling, aluminum headed 434 inch Pontiac and a Tremec 5-speed. He asked why I wanted such an "Antiquated" car. I explained that I had owned them before, and added that Car&Driver's road test of a new Camaro SS and a new SRT8 Challenger said the Challenger pulled .85g on the skidpad, and the Camaro .88. I pointed out that C/D's 1979 Trans-Am test car pulled .82g on 225/70R15 Goodyear Polysteel Radials. If the old T/A had been shod with the modern cars 245/45ZR17, and 275/40ZR17 rubber, it would have easily surpassed those numbers. Doesn't take a mathmetician to figure that out. Ditto for drag tests. I'd like to see what a for-real '60's L88 427 Corvette would do in the 1/4 with the 335/35ZR20 tires that a modern Z06 has!!  Lets' run an LS6 Chevelle on something fatter and stickier than F70-14 Coker tire Wide Oval repros shall we?  Or a Hemi 'Cuda on something other than repro Polyglas GTs!!  Anyhow I just had to vent that-sick of hearing the "Greatest Ever" label put on some person or thing that is really just "cool now" not the "greatest ever".            

Sunday, January 27, 2019

Some alternative bodystyles that can be way cool....

There's a lot of cool cars that everyone overlooks when their searching for their "dream car."  Here's a few I thought of.  # 1. 1960-68 Full-size Pontiacs. While 99% of Chevy Impalas,Caprices, and Biscaynes of this era are small-block powered, and 396, 409 and 427 versions bring a King's Ransom-the Pontiacs are a steal. Every single Catalina, Bonneville and Gran Prix built has at least 389 cubes under the hood, and depending of year-some have 400, 421 or 428!! 1965 and later models with automatics will have the excellent TH400.  Any suspension or brake upgrades that fit an Impala will fit these cars. # 2. 1963-69 Full-size Fords. The '63 Galaxie hardtop is still a great looking car 50+ years later, and the later models are cool too. '60s Fords had luxurious interiors, and most have 390 cubes under the hood. Later LTDs had hidden headlights and 428 or 429 motivation. # 3. 1969-76 Pontiac Gran Prix. While Rat-Powered Monte Carlos are rare and expensive, GPs had 400 cubes standard all years and a fair number of "SJ" models had 455s. Wrist-thick front and rear sway bars made them amazing handlers for a big car. # 4. 1967-69 Thunderbird. I personally think this is one of the best-looking cars Ford ever produced. 390, 428 or 429 cubes for power, and luxurious interiors. I like the 2 dr models, but the 4-door versions with the "Suicide Doors" have a following too. # 5. 1966-69 Buick Riviera. These had the swoopy, fastback,hidden headlight styling of the revolutionary Olds Toronado, but were still rear-wheel drive. With 430 cubes under that long hood they move pretty good too. # 6. 1969-72 Plymouth Sport Fury. Peter Graves drove one of these on "Mission Impossible". With 383, 400 or 440 cubes under the hood they have great potential. # 7. 1967-69 Cadillac Eldorado. These cars styling still looks futuristic today. And with 429, 472 or 500 cubes they've got the torque. A little heavy to be a hot rod, but man what a great cruiser. # 8. In the same vein-I really like the 1972-76 Lincoln MKIV. Hidden headlight styling,luxurious interior and 460 cubes for motivation. Too heavy to be a serious hot rod, but a great, comfortable cruiser that looks cool.  Mastermind

Saturday, January 19, 2019

Some overlooked gems...

There are a lot of overlooked gems out there with potential that people don't think of.  # 1. 1976-77 Olds Cutlass 442. The last W30 455 went away in 1972, and by '73 the 442 became an "Appearance and Handling" package on the Cutlass. The "Station wagon" 455 hung around til '76-but their rare and wheezed out 190 hp-a far cry from the 370 of the of the '70 model and the 300 of the '72. However-the graphics were cool, and the suspension, with wrist-thick front and rear sway bars made the cars handle better than anything except a Pontiac Trans-Am. The body was so aerodynamic that Richard Petty switched to a Cutlass after his 1974 Charger body was outlawed. Their fenderwells will accomodate huge tires-up to 275 / 60 R15 on 8 inch wheels. The 350 and 403 models are the ones to look for. Edelbrock claims 397 hp and 400 lbs of torque from their Performer RPM package on a 350. On a 403 you'd be well over 400. The other thing you'll need is an axle-ratio change. These cars came stock with 2.41:1 gears. Switching to something in the 3.23:1 to 3.73:1 range will give you a huge improvement in performance. So much that this should be your first step, or the only step even if you leave the motor bone-stock.  # 2. 1977-81 Z/28 Camaro. Seeing the monumental sales success of the Firebird Trans-Am-( Pontiac sold nearly 50,000 in 1976 alone; and another 68,000 in '77. "Smokey and the Bandit" was released in May 1977; that sales bump wouldn't be felt until the '78 model year when they sold 93,000 ). Chevrolet hastily resurrected the Z/28 which had been on a 2 1/2 year hiatus since 1974. It was a good package featuring T/A style spoilers and graphics, and upgraded suspension with front and rear sway bars. Power was the ubiquitous 350 V8 backed by a T10 4-speed manual or a TH350. 4-speeds got 3.73:1 gears and automatics got 3.42:1s which really put the power to the ground and put some "Right Now!" into acceleration. '78 models got Firebird style urethane bumpers replacing the ugly steel ones of the '77.  1980 brought back "Cowl Induction" a vacuum-operated hood scoop that opened at full throttle and sounded cool, and bumped power by 10 hp to 190. 4-speed models had 3.44:1 1st gear ratios and 2.28:1 2nd, with a 3.08:1 rear axle. This gave better acceleration, higher top-speed and better gas mileage than the 2.64:1 low gear / 3.73:1 axle of the '77-79 models. Automatics still got 3.42:1 gears. For some perverse reason in 1981-you could only get a 350 with the automatic. If you wanted a 4-speed you got a 305 which wheezed out 145 hp. It wasn't emission laws-you could still get a 350 / 4-speed combo in an '81 Corvette. If you have or want to buy a 305 model-a 350 is a bolt-in swap. There's more speed equipment for a small-block Chevy than anything else on the planet so these cars have awesome hot-rod potential.  # 3. 1980-81 Pontiac Trans-Am. These are only bargains if your considering an engine swap. Here's why-you had 3 engine choices. An anemic 301 Pontiac that wheezed out 135 hp, a 301 with a Turbo that was rated at 210-but had nowhere near the performance of the '79 and earlier 400s that supposedly had 220. Hot Rod's 400 / 4-speed '79 test car ripped off a blistering 14.61 second 1/4 mile. Popular Hot Rodding's '79 Formula ran a 15.0.  Their 1980 Turbo test car could only manage a 16.3!  Yet it's only down 10 hp? Riiigggghhht.  The third choice was a 305 Chevy. The upsides are a 400 or 455 will bolt right in place of a 301, and a 350 or 383 Chevy will bolt right in place of the 305. # 4. 1982 "5.0" Mustang. For this one year only you got a 302 V8 with a 2bbl, and 4-speed stick or a 3-speed automatic. Theirs a ton of speed equipment for small-block Fords, so these have great potential. Ford guys snub them in favor of the '83-86 models which have 4bbl carbs, 5-speed sticks and 4-speed automatics. But it keeps the prices on these dirt-cheap, and a 4bbl carb and intake change is a no-brainer. # 5. 1984-86 Olds Cutlass 442. These "G" bodies have cool graphics, great handling suspensions and gorgeous interiors. Power is unfortunately a 307 Olds V8 that wheezes out 140 hp. The upside is a 350 or 403 Olds V8 is a bolt-in swap. Backed by a TH200R4 and 3.42:1 axle that came with the 442 package-this combo could be a real sleeper.  # 6. 1989 20th Anniversary Trans-Am. These cars have the WS6 suspension and the vaunted Turbo 3.8 V6 out of the fearsome Buick Grand National. The Turbo V6 is both lighter and has more power than the 305 and 350 Chevy V8s, so the already stellar handling is improved as well as acceleration. These will bring a King's Ransom-but their worth it.  Mastermind        

Thursday, January 17, 2019

"Magnum Force" is easier and cheaper than you think....

If your a Mopar guy and your looking for some major power for low bucks I have the just the ticket. There's millions of them in junkyards. From 1992-2003 millions of Dodge trucks and vans and Jeep Grand Cherokees had 5.2 and 5.9 liter "Magnum" V8s. The 5.2 ( 318s ) make nice drivers and could be really quick in very light car like a Duster / Dart. For serious power you need the 5.9 ( 360 ). I've always liked the 360 Mopar as a performance engine. The "hot" setup for small-block Chevy racers has always been slant-plug heads and 6 inch connecting rods. Mopar LA engines have angle-plug heads and 6.123 inch rods from the factory. The "Magnum" heads breathe better than any other factory head and many aftermarket ones. They will bolt up to earlier ( 1971-91 ) blocks. You will need a "Magnum" bolt-pattern intake and Edelbrock has you covered. The "Magnum" engines have roller cams from the factory. Crane, Comp Cams, Lunati and others offer high-performance roller cams. Eagle and other companies offer stroker crank kits to get 408 inches. With proper cam, intake and headers, it's pretty easy to get 400 hp and 450 lbs of torque from a "Magnum" engine. That's enough to make any street car an absolute rocket. So think outside the box-you don't always need a 440 or a Hemi to make big power. Mastermind  

Sunday, January 13, 2019

I don't disparage anything....I just tell the truth!!

Sometimes people get on me for being "down" on certain makes and models. I'm not "down" on anything; I just give my readers my honest opinion, which I hope will help them make informed decisions before they spend a large amount of money on a project. Lately several people have asked why I "Hate" Fords. I don't hate Fords; I've owned two Ford Pickups both bought brand-new and paid off and kept about 8 or 10 years. I've owned two Mustangs one a '66 289 GT  the other an '83 "5.0".  I'd love to have a 390 powered '67-70 Cougar if I could find one that wasn't priced in the stratosphere. Ditto for a 1970-71 429 T-Bird. If I buy another used work truck it'll probably be a '70's, '80's or 90's F150 or F250.  I don't "hate" Fords. Some people got this impression from a few posts I wrote several years ago. One was about classic movie car chases. I talked about "Bullitt".  Everything I said was from an interview with Stunt Coordinator Carey Loftin from way back in 1987.  Ford had a contract to supply cars for movies with Warner Brothers.  Steve McQueen didn't want two Fords in the chase. He thought it would be hokey that both the cops and bad guys would be driving Fords. Chrysler and GM wouldn't give them any cars, citing Ford's contract with Warner. Loftin and McQueen went to a Bay Area Dodge dealer and bought the Charger with their own money. The Charger was a 440 / 4-speed. The five Mustangs supplied by Ford were 390 / 4-speeds. A little history-when GM debuted the Camaro and Firebird in late 1966 for the '67 model year Ford was caught with their pants down. The 302 Z/28 would run circles around the 289 Mustang. Worse yet-you could get a 396 Rat Motor in a Camaro and a 400 ( the same engine in the mighty GTO ) in a Firebird. All a 289 Mustang would see of a 396 Camaro or 400 Firebird is the taillights. Ford hastily dropped the 390 in the '67 Mustang. However-unlike the 396 Chevy or 400 Pontiac-the 390 was not a high-performance engine. It was a low-revving high torque towing engine used in "big" cars like LTDs and station wagons, and trucks. One of the buff magazines tested the big-block pony cars and the Chevy and Pontiac ran off and left the Mustang. I mean badly-by half a second or more. The Mustang ran something like a 15.6 in the 1/4; the automatic Firebird ran a 15.1-a five car length drubbing, and the 4-speed Camaro ran something like 14.7-a nine car length drubbing. Anyhow-in early practice the 440 Charger would run off and leave the Mustang so badly that they couldn't film it. Steve McQueen was furious. Loftin and his mechanic Max Balchowsky hopped up one of the Mustangs with headers, an Edelbrock intake and double-pumper Holley carb and a Mallory distributor. Now McQueen and stuntman Bill Hickman ( who drove the Charger ) could successfully play cat and mouse. However-bounding over the streets of San Francisco at speeds up to 115 mph-the Mustangs were falling apart-breaking shock towers and suspension parts, door handles coming off etc. Loftin and Balchowsky worked every night taking parts off the other cars to keep the camera car running. That's why only two of the five still exist; the other three were crushed. Meanwhile-the Charger with it's torsion bar front end and Dana 60 rear had no problems other than throwing hubcaps off. If you watch the film-the Charger loses 8 hubcaps in the chase. People say this really "bashes" Fords. How?  It's the truth straight out of the mouth of the man who lived it. What did they want to me do? Lie?  The other things I've been called out on are saying that Ford's are a nightmare when swapping engines. Guess what? They are. Unlike a small-block Chevy or a Pontiac or an AMC or a small or big-block Chrysler where almost everything interchanges regardless of model-every Ford is different. A 390 in a Mustang uses a different oil pan and accessories and mounting points than a 390 in an LTD, which is different from a 390 in a T-Bird, which is different than a 390 in an F100 Pickup!!  A 289 / 302 has a different bellhousing bolt-pattern than a 351C, which is different from a 390 / 428, which is different from a 429 / 460.  Not the same as bolting a TH350 from a '79 Camaro into your '65 Chevelle and not having to change anything !!!  ( A Powerglide and a TH350 are not only the same length and have the same bellhousing bolt-pattern, but also use the same rear trans mount and driveshaft yoke!! ).  I just stated an irrefutable fact-Ford stuff does not interchange as easily as GM or Chrysler stuff. That's good advice for novice engine swappers to know, not a "slam" on any product. The other thing I've been taken to task for is when discussing carburators I've said the Autolite 4300 was the worst carb ever made. Guess what ?  It Is!!!!  My dad and I worked for Ford in the '70's. If you had a 351C Mustang or Torino, or a 460 T-Bird or Lincoln ( all of which used that awful 4bbl ) you enjoyed hard starting, especially in cold weather-hesitation, stumbling, crappy gas mileage, ( I mean 5-8 mpg on a brand-new car ) and all around awful performance. They were terrible when they were brand-new. Some of these cars didn't have 5,000 miles on them. If the customer bitched hard enough Ford Dealers would replace the 4300 with a 600 cfm Holley with an Electric Choke and cover it under warranty!!  The part number was 6619 or 6919; I think the throttle linkage was the difference-one for sticks and one for automatics.  I remember because as a parts guy I ordered so god damnded many of them!! With the Holleys the cars ran like a champ!!  The main reason GM and Chrysler musclecars ran so good was they had decent carburators. GM used the great Carter AFB until 1966. Early Q-Jets ( '66-67 ) had a few problems but they were ironed out quickly. Through the late '60's and all of the '70's Quadrajets were bullet proof. ( Some Chevys had 3310 Holleys and they worked good. )  Mopars had the excellent Carter AVS until 1971. The Thermo-Quad worked good on 340, 360 and 400-440 engines in the '70's. Meanwhile-Boss 302s and 429s had Holleys as did 428CJ's; some 429CJ Torinos actually had Quadrajets. Everything else limped along with that awful 4300. Again-what do people want me to do? Lie and say they were great?  I've said many times that Chrysler was light-years ahead of GM on automatic transmission technology when they introduced the Torqueflite in 1962. It was far superior to GM's hydramatics and Powerglides. The TH400 introduced in 1965 was just as good; but oddly they were only available in "big" cars. If you wanted a GTO or a Chevelle or 442 with an automatic you got the awful Two-Speed Powerglide / ST300 !!! A TH400 wasn't available in an SS396 or GTO or 442 until 1967!! In a Corvette until 1968!!  I'm sorry if the truth hurts some people's feelings. Here's another example-a lot of people say I'm "Biased" to GM stuff. Again-not true I already stated my feeling on Fords. I've owned "Bullitt" Chargers. I'd love to find a "Vanishing Point" '70-74 Challenger, a Charger-based 383 '71 Super Bee, or even a '78-79 Li'l Red Express Pickup.  I like Mopars fine. But yet I've been called out for saying that nothing makes as much power for as little money as a small or big-block Chevy. Again-that's an irrefutable fact. Their's more speed equipment on the market for a small-block Chevy than anything else on the planet. The small-block Chevy is usually the test mule for anyone introducing anything new!!  Like it or not they offer the most "bang" for the buck. Sure, a 360 Mopar, or 360 AMC or 350 Olds, or 351W or 351C Ford can run every bit as strong as a 350 Chevy. At 2 or 3 times the cost. Ditto for the big-blocks. Like it or not-Nothing makes more power for less money than a Chevy Rat Motor. Yes a Chrysler Hemi or Boss Nine Ford can make as much or more power-at two or three times the cost. Cases in Point-GMPP sells 454HO crate engines for $5995. Their rated at 440 hp and 500 lbs of torque. A Mopar Performance 426 crate Hemi makes 465 hp and 490 lbs of torque. And sells for $ 14,995.  GMPP's "King Kong" Rat-the 572-makes 720 hp and sells for $17,995.  Mopar Performance's 528 Crate Hemi makes 625 hp and sells for $22,725.  Jon Kaase has a 600 inch Boss-Nine that makes 912 hp and 826 lbs of torque. For the tidy sum of $36,999!!!   The same goes for other restoration parts-be it body parts, interior trim, suspension parts, etc. GM stuff if going to be the cheapest, followed by Chrysler, then Ford. AMC people have a real rough time. A Chevelle or GTO is going to cheaper to restore than a Road Runner. A Mustang is going to be way easier and cheaper than a Javelin. Like it or not that's the state of the business right now. Parts companies are in business to make money. Your going to sell a lot more stuff for a '70-81 Camaro / Firebird than you are of something that only fits '72-73 Mercury Montego GT's!!!  The same for sports car guys. A Triumph Spitfire or MGB is cheaper to restore than  a Datsun 240 / 260 / 280Z, which is cheaper to restore than a Porsche 911, which is cheaper to restore than a Ferarri 308 GTS !!  So I'm not "Bashing" anything when I'm giving advice; I'm trying to save people money and frustration!!  If that's "Biased" then I guess there's nothing I can do about it. Mastermind              

Wednesday, January 9, 2019

Little things can become big things....

In the same vein as the last post, I can't stress enough how important it is to fix little things before they become big problems. Here's a good example. I touched on it before, but it's worth re-visiting. Back in the '90's when I had a custom restoration shop I had a good customer base. They brought me big projects; however most of them got their oil changed at Jiffy Lube, or their tires rotated at Big O. Sometimes these repair places would try to sell my customers huge repairs, and often they'd come to me for a 2nd opinion. One was a guy with a '77 Trans Am. It had a 400 Pontiac backed by a TH350, the standard powertrain that year. ( A 4-speed was a no-cost option ). One of the big tire chains told him he needed a new transmission. I drove the car, and it did shift erratically and very hard when it did. Upon inspection I changed the fluid and the filter. I also discovered that the rubber line to the vacuum modulator was severely cracked and spewing fluid. I replaced the modulator and the rubber line. Now the car shifted smoothly at part-throttle, and under full-throttle would lay 8-10 feet of rubber on the 1-2 shift. I charged him for the fluid change and the modulator and the labor to change that. He was escatic. Instead spending over $1,000 for a rebuilt TH350, which he was almost sure he was going to have to spend, he got off for less than $200. The symptoms certainly indicated that the tranny might be toast-but it turned out to be the modulator-a minor repair. The other case was guy with a 396 Impala. Another shop told him he needed a new engine. I drove the car, and for a big-block Chevy it was definitely a "dog". It couldn't even spin the tires on dry pavement and just fell flat on it's face under acceleration. I did a compression test and all 8 cylinders were within 5 to 10 psi of each other. Upon further inspection I found multiple problems. None insurmountable-the car was just suffering from terminal neglect. The automatic transmission kickdown wasn't hooked up, the carb was way too rich, the timing was way too slow,the plug wires were bad, and the vacuum advance was unplugged, and the points were closing up. I fixed these minor problems-i.e. installed new, properly gapped points and wires, plugged in the vacuum advance, leaned out the carb, set the timing to spec, and hooked up the kickdown. Now the car would smoke the tires all the way across an intersection, get rubber into 2nd, and pull like a Rat Motor should. The owner was so happy that he tipped me $100 over the bill I charged him. He was ready to spend a couple grand or more on a new engine, and got a new lease on life for a couple hundred instead. The moral of the story is fix the little things before they become big things. The guy with the T/A-his bad modulator would have eventually caused the trans to lose enough fluid that it would burn up, and need to be replaced. The guy in the Impala could have limped along long enough that his over-rich carb and slow timing could have washed oil off the rings or caused it to spin a bearing or the cam to go flat. I had a guy with a '74 Nova SS bring his car to me one time. It was a cute Nova hatchback and it had a 350 with a 4-speed. It too, was a "dog" that fell flat on it's face under acceleration, and it sounded like a garbage disposal. It had headers on it and dual exhausts and an Edelbrock Performer intake with a 625 cfm Carter AFB carb. It should have been a screamer. Upon opening the hood I saw the problems. It had massive exhaust leaks. The header gaskets were totally blown out, and whoever had installed the intake manifold hadn't blocked off the EGR!! With massive vacuum leaks like that, I was amazed that it ran at all. I replaced the header gaskets. Edelbrock manifolds usually come with EGR plugs. I had some laying around because I installed so many in my shop. After sealing the leaks and adjusting the carb and timing a little, I went for a drive. Now it would rocket off the line, spinning the tires most of low gear. Powershift, get the satsifying rubber-in-second screech, and keep going. Now it pulled hard to 5,500 rpm, and would spin the tires with ease in low gear. The car's owner was doing handsprings. He couldn't believe the fix was that simple. I had another guy that had a '72 El Camino with a very expensive 383 crate motor that didn't run much better than the tired 307 with a 2bbl that it replaced!! There was nothing wrong with the engine. It sounded badass, and felt like it had a ton of torque. But the car wouldn't run very fast, and the gas pedal felt really, really stiff. I discovered that the throttle bracket was bent and the cable was sticking. So bad that it wouldn't allow the secondaries on the carb to open at all. It was restricted to maybe half-throttle. I got a new bracket and cable and adjusted it so the throttle linkage would open fully. The test drive after was mind-blowing. Now the Elky would literally spin the tires as long as you wanted to stay on the throttle. When it had traction, it was a rocket. I told the owner he'd have to play with launch technique to get the best start, but the car now had more than enough power!  Yet one simple thing was killing it's performance. So don't let something minor cause you a major problem. Mastermind    

Monday, January 7, 2019

Don't put the cart before the horse....

A lot of people ask what's the 1st thing I should do to get more performance out of my musclecar? Or what one modification offers the most "bang" for the buck?  Every car line is different, so there's no one pat answer. However there are things you can do to greatly increase your car's performance without throwing major bucks and tons of parts at it. Here's the things I'd do BEFORE I pull out my Visa card and call Summit, or PAW or Jeg's!  # 1. Make sure it's running properly, even if it's bone-stock. I can't stress this enough. I see so many musclecars limping around on 6 or 7 cylinders. And I'm not talking beaters, rat rods or works in progress. I see it every Hot August Nights-cars with $5,000 paint jobs and $2,000 worth of tires and wheels that can't smoke the tires on dry pavement or pull 5,000 rpm in low gear!  These cars have bad plug wires, the vacuum advance is inoperable or not hooked up,the points are closing up, the timing is way too advanced or way too retarded, the carburator is way too lean or way too rich,the throttle linkage is sticking or not opening all the way, the automatic trans kickdown is not hooked up, the vacuum modulator is disconnected or spewing fluid. I talk to these people-and they'll have $40,000 invested in the car-and they can't tell you the last time they changed the spark plugs and wires or the points , distributor cap and rotor or the fuel filter!! Even on a stock engine bad tuning or excessive neglect can cost you as much as 50 hp. Make sure everything is right before you start spending money or changing things. # 2. Intake and exhaust. Regardless of make and model I'd say here is where you get the most "bang" for the buck. Especially if the car has a 2bbl carb and single exhaust to start with. A factory or aftermarket 4bbl carb and intake setup will really "wake up" any 2bbl motor. Besides much more power, you'll have better drivability and probably better gas mileage. Even if you don't want headers, a good, free-flowing dual exhaust system can be worth as much as 30-40 hp on a stock engine with iron exhaust manifolds. Look at the car's under side on the rack. Many factory "dual" exhaust sytems are not true duals, and are very restrictive. I hate the "crossflow" muffler used on '67-74 Camaros and Firebirds. They cost the stock engines 25-30 hp. That's why the RAIII and RAIV 400's are rated at 335 and 345 hp in a Firebird or Trans-Am and 366 and 370 hp in a GTO. The GTO's duals all the way back were worth 25-30 hp bone-stock!! If you read road tests of a 71 455HO Trans-Am and a '71 455HO GTO-the GTO is nearly 1/2 a second quicker in the 1/4, even though it's a slightly heavier car!! ( 4,070 lbs vs 3,731 ). Some other "geniuses" will tell you about GM's 10 lb per hp rule-but their full of shit. 1st off-this rule apparently didn't apply to Corvettes-a mid '60's Stingray weighs about 3,300 lbs and you could get a 427 with 390, 425 or 435 hp!!  Ditto for Chevelles. A '65 Chevelle weighs about 3,400 lbs, yet was available with a 375 hp 396. As was the supposed "3,250 lb" '67-69 Camaro!!  The 10 lb per hp rule is a guideline used to beat the insurance Nazis. Most of the engines were actually under-rated!!  A W31 Cutlass with special heads,an aluminum high-rise intake, special exhaust manifolds, a special flex-fan and a hot 308 degree cam that doesn't make enough vacuum to operate power brakes and requires a 4-speed and 3.90:1 or 4.33:1 gears only makes 325 hp when the standard "station wagon" 350 makes 310??!!!  Puhleeze. And I've never seen ANY Cutlass that weighed 3,100-3,250 lbs, not the original '64, and damn sure not the larger '68-70 models which like the GTO were pushing 4,000!!  My dad and I worked for Pontiac back in the day-and no 400 Firebird ever weighed 3,250 lbs!!! ( The standard 400 was rated at 325 hp;the same engine in a GTO or Grand Prix had 350 hp ). The Firebirds were 3,500 on up all day-especially with power steering, disc brakes, etc, which most of them had. Other geniuses will talk about a tab on the carburator restricting throttle opening to limit power. I have seen these cars come off the truck and have PDI'd them when brand-spanking new, and I have never seen one. Regardless-Ford Mustangs-even 390 and 428 models had restrictive exhausts as well. True duals all the way back will help any car regardless of brand. # 3. Mechanical advantage. Gears make it go. Most '70's cars have salt-flats gearing like 2.56:1 or 2.73:1. Switching to something in the 3.23:1-3.73:1 range will give you a huge boost in acceleration without hurting fuel economy or drivability too much. If you have an automatic transmission a mild torque converter upgrade can help immensely especially with small-blocks. Most stock torque converters have a stall speed of 1,200-1,700 rpm. Upgrading to one with 2,000-2,200 stall speed will give you a jackrabbit start without excessive wheelspin. Converters with 2,500-3,000 stall rpm on up are fine if you have a radical cam and 4.10:1 gears; however especially with big blocks you may blow the tires off without slicks or drag radials. Conversely, if you use a 3-grand converter with 3.23:1 gears-you may burn the transmission up! Your 65 mph cruise rpm will be less than the converter's stall speed which will create slippage and excessive heat. If your cam has less than 220-225 degrees duration ( @.050 ) you don't need a high-stall converter. And you have to remember most industry "guidelines" are based on a 350 Chevy; a cam that's "too radical" for a small-block Chevy might be a sweetheart in a 440 Mopar, 455 Pontiac or 460 Ford. See what I'm saying?  Another easy improvement is a shift improver kit for automatics. I personally like the TransGo kits the best; I have also used the B&M kits and they are excellent as well. I wouldn't use an "off brand". Use the "Street" or "Street / Strip" setting to get firm,precise shifts. If you use the "Competition" setting you will get excessively hard shifts even at part-throttle and the car will be practically undrivable.  # 4. Electronic Tuning. If you have an '80s Camaro / Firebird or Corvette or Buick Grand National or "5.0" Mustang there are things you can do to really help 0-60 and 1/4 mile times without spending big bucks. If you have a carburated LG4 / L69 305 Camaro or Firebird an Edelbrock Performer EGR intake will make a huge improvement. I'd also use some Hedman Shorty headers with 02 hookup. The electronic Q-Jet will self-adjust to these minor changes so you won't have to re-jet the carb. I'd also switch to a 160 thermostat ( and on L69 cars get the switch from Summit that turns the electric fan on at 185 instead of 220 ). If you have an L98 or LB9 Tuned-Port Injected engine, the first thing I would do is get a 160 thermostat and the fan switch that turns the fan on at 185 instead of 220. These engines at 220-are on the edge of vapor lock and often stumble under acceleration. By reducing running tempurature to 185-nearly 40 degrees-your getting a cooler, denser fuel charge. No more stumbles, and smooth acceleration all through the range. The other things you can do-Accel and Edelbrock offer ported baseplates and runners that will ad 20-25 hp and don't require any changes to the stock ECM. These simple things will give you a HUGE improvement in performance and drivability. The same goes for Regal T-Type / GN owners. By going to the 160 thermostat and changing the fan switch you'll knock 3 /10s off your 1/4 mile time. 40 degrees cooler fuel charge on a Turbocharged, Intercooled engine can make that much difference. I'd also run 91 octane Chevron or Shell gas and a can of octane booster. The ECM is programmed to detect detonation and retard the timing accordingly. You'll get way better performance with brand-name 91 and octane booster than you will with 87 octane cut-rate gas. It sounds too simple-but you'll feel it in the seat of your pants. This isn't electronic but the performance boost will be huge. Most '83-95 "5.0" Mustangs, either stick or automatic, have either 2.73:1 or 3.08:1 gears. Switching to 3.55:1 or 3.73:1 gears will give you a stunning improvement. And not just off the line-you'll feel it in 2nd, 3rd and 4th as well.  When I swapped the 3.23:1s in my Hurst / Olds for some 4.10:1s  I didn't notice any improvement in low gear. Apparently the 455 had enough torque to launch the car regardless of gearing. However, the difference in 2nd and 3rd was monumental. The gear swap is the first thing I would do to a "5.0". After that-Edelbrock and Trick Flow offer ported manifolds, larger throttle bodies,cylinder heads, cam kits etc. The Trick Flow top-end kit-( heads, intake,and cam ) claims 350 hp. Quite a bump from the stock rating of 225!  Hope this helps everyone out. Mastermind            

Sunday, January 6, 2019

More on the path of most resistance.....

I guess since the majority of the 117,000 T/A's sold in 1979 ( only 10,000 had the 400 Pontiac / 4-speed powertrain ) were 403 Olds / TH350 models-a lot of people are interested in converting them to a stick. As I apologized for in the last post-there are aftermarket flywheels available. You still have to chase down a bellhousing, the linkage, the pedals, and the shifter, as well as the disc, pressure plate and throw-out bearing. Like I said in the last post one monkey wrench I see is most L80 403 cars had 2.41:1 or 2.56:1 axle ratios. A few WS6 cars had 2.73:1 or 3.23:1 gears. 3.23:1s would be perfect. The others not so much. However- even with 2.56:1 gears there's a couple ways you can go and still have the acceleration your looking for. Borg-Warner ( and Richmond today ) made T10 4-speeds with a 3.44:1 1st gear and a 2.28:1 2nd. These were used in 1980-81 Z/28 Camaros, 1981 Trans-Ams ( behind a 305 Chevy ) and 1982 Z/28 Camaros and Trans-Am Firebirds. The 2nd choice is also a T10 that was used in 1980-81 Corvettes. These have a 2.88:1 1st gear and a 1.91:1 2nd.  Summitt Racing and PAW and other parts companies also sell both of these new. The low ( higher numeric ) gearing in 1st and 2nd will give you the torque multiplication to get going quickly. By 3rd and 4th the car will be going fast enough that it won't matter, and the 403s 325 lbs ft of torque will keep pulling. Top speed will be something like 135 mph at 4,500 rpm, and you'll have easy freeway crusing. The 403s had 325 lbs of torque at 1,600 rpm. Much lower than the 400 Pontiacs 320 lb peak at 4,000 rpm. You'll have to play with launch rpm to see which gets you out of the hole quickest. I'd start with 2,500 rpm and go from there.  The 403s tractor-like torque curve will demand 4,500-4,800 rpm shift points for best performance. I speak from experience on this. My 403 powered '77 T/A ran quickest when I shifted manually at 4,900 rpm ( 1-2 ) and 4,400 rpm ( 2-3 ). After I installed headers and a Holley Street Dominator intake and switched from R46SZ plugs ( an .080 gap ) to R45S ( a .040 gap ) it would pull to 5,400 rpm. However, because of the lazy stock cam it didn't really make any more power above 5,000; I was just beating up the valvesprings. Even with the intake and exhaust upgrades ( which helped immensely ) it still ran best with sub-5,000 rpm shifts. Obviously if I'd put a bigger cam in it, that would have changed. Anyhow-you can make this conversion work, and it will be fun to drive, especially if you invest in an Edelbrock Performer intake ( the Holley Street Dominator is out of production, but their great if you can find one at a swap meet ) and matching cam, and headers and dual exhaust. Not to be Devil's advocate-but like I said previously-if you did those engine mods and then swapped in some 3.23:1 or 3.42:1 gears and a shift kit and 2,000 rpm converter in a TH350 model, you'd have the same or better ( less wheelspin ) performance with a lot less expense and grief. Or you could just buy a 400 / 4-speed Pontiac model. But if you "gotta have" a 4-speed in your 403 'Bird, it is possible and relatively easy ( mechanically speaking ) to do. You could use a Muncie or other T10s-but 2.20:1, 2.43:1, or 2.52:1 low gear and 1.61:1 2nd won't have nearly the acceleration of the 2.88:1 or 3.44:1 low models. The other question I get a lot is people asking about multi-carb setups. I personally love multi-carb setups. My dad had a '59 Catalina with the Tri-Power 345 hp 389. He also had a Tri-Power 376 hp 421 powered '65 2+2. He was a wizard at tuning and synchronizing multiple carbs. I spoke in a previous post about him being recruited to tune both cars in a match race. One was a 440 / 4-speed / Six-Pack GTX, the other was a 426 Hemi / Torqueflite Road Runner.  The Road Runner won by 1/2 a fender length. He also had big following of Import customers-tuning the multi-carbs on Jaguars, Datsun 240Z's , Porsche 911s, Ferraris. I had dual-quads on My Judge. A buddy had a 440 / Six-Pack Super Bee, and another guy I hung out with had a Tri-Power 435 hp 427 'Vette- ( that my dad tuned ). The buff magazines say a single 4bbl is better because their easier to make idiot-proof. I'm serious. I see it every Hot August Nights. Doesn't matter if it's a Hemi Mopar, or a 427 Stingray, or a 409 Impala, or a Tri-Power GTO or whatever. Guy has this pristine, restored car that he's so god damnded afraid of blowing up that he drives like grandma on Prozac, if he drives it more than on and off the trailer! The car never sees the high side of 3,000 rpm. Then, the second it fouls a spark plug, they start screwing around with the carburators. Pretty soon it won't even start. Now-if these guys had any sense they'd do one of two things. ( A ) Once in a while-like the GTO song-you need to "Turn it on, wind it up, blow it out". Make a full-throttle run down the freeway or through the gears. Or ( B ) If your going to drive like a little old lady-then go a range or two hotter on the plugs to keep them from fouling. If you decide to take a long trip or go the drags-changing the plugs to the proper heat range is easy. Anyway-multiple carbs look and sound cool and make as much or more power than single 4bbl setups. Besides the factory setups Edelbrock sells Tri-Power and dual-quad manifolds for small and big block Chevys, small and big-block Fords, Mopars , and Pontiacs. Redline sells 4-Weber setups for small and big-block Chevys and small and big-block Fords. I worked on a Monster Truck that had 4-Webers on a 454 Chevy burning alchohol!!  It shook the earth, and won the truck pull!! The main thing is err on the side of caution. If you've got an 11:1 440 Mopar with a 4-speed and 4.10:1 gears, dual 750 AFB's or Edelbrocks will really rock. On a 9:1 289 Ford with an automatic and 3.25:1 gears, maybe three 2bbl 160 cfm Edelbrock 94s or two lean-jetted 450 Holleys or 500 AFBs would be a better choice!!  Manufacturers, both Import and domestic went to single-carbs and later fuel-injection because of ever-tightening emission standards, not lack of power. If you decide on a multi-carb setup, spend the money to get an expert to tune it, and then leave it alone!!  The other thing that hot-rodders screw up on is "We shall overcam". They'll listen to some idiot in an auto parts store and get something way too radical for their application. Obviously, larger engines and manual transmission cars can tolerate more "cam" than small-blocks and automatics. Regardless of engine size or transmission it's better to err on the side of caution. In general-if you have 225 degrees or less duration ( @.050 ) lift-you'll have a good idle and can use a stock torque converter. If you go more than that you'll need a stick or a 2,500+rpm torque converter and some low ( higher numeric ) gears. The Cam manufacturers catalogs give good guidelines-i.e.-works with stock converter, or needs 3.42:1 gears, etc. You have to take the whole package into account, not just engine size. Here's a perfect example. Two Pontiacs. One, a '68 GTO, the other a '78 T/A. Both guys install the vaunted "Ram Air IV" cam which has 231 / 240 duration ( @.050 ) and .470 lift. The '68 GTO will absolutely rock with this cam. The '78 T/A will not idle, will cough and spit and not run as good as stock. Here's why. Both have 400 V8s. The '68 GTO has 10.75:1 compression, a 4-speed and 3.55:1 gears. The '78 T/A has 8:1 compression, a TH350, and 2.56:1 gears. The hot cam will make the GTO Rock, and the T/A stumble. See what I'm saying?  Anyhow-build your car however you want-it just may cost more than you'd like. Mastermind        

Tuesday, January 1, 2019

I stand corrected....But I still wouldn't attempt it....

Since I'm very good at crowing when I'm right, I feel obligated to admit when I'm wrong. In the previous post I said no one offered a manual transmission flywheel for a 403 Olds engine. A friend sent me a Summit Catalog and a company called Ram-that makes high-performance flywheels for various vehicles does offer a manual trans flywheel for 330-350-403 Olds engines. So-to the guy with the Disco-era T/A who wanted to convert his 403 / TH350 'Bird to a 4-speed-it is possible. However-the hassle and expense of chasing down a Muncie or T10 trans, a manual trans crossmember,a Bellhousing,the clutch fork and linkage, the pedals,the disc, pressure plate and throw-out bearing, the shift linkage, and cutting a hole in the floor for the shifter is still the monumental pain in the ass and the wallet that it always was. Further-most L80 403 / TH350 T/A's had 2.41:1, 2.56:1 or 2.73:1 gears, none of which will work well with a stick. You'll need to swap in some 3.23:1 or 3.42:1 gears to get the performance increase your looking for. And here's the "Catch 22" on that-if you put 3.23:1 or 3.42:1 gears, a TransGo or B&M shift kit and a 2,000-2,400 rpm converter in the TH350 model-you'd have a spectacular improvement in 0-60 and 1/4 mile acceleration, and a lot less expense and grief of doing the stick change-over!!  So my original advice is still good advice-if you "Gotta Have" a manual transmission Firebird-just buy a T/A or Formula 400 that has a stick from the factory!  On the same subject someone had asked me about putting a manual trans in a '78-88 "G" body-i.e.-Grand National, Monte Carlo, Gran Prix, Cutlass, etc. Their rare, but GM did offer stick shift models in the late '70's and early '80's. I personally know 3 people that had them. A friend had a '78 El Camino with a 350 and a 4-speed. A guy I worked with had a '79 Gran Prix with a 301 V8 and a 4-speed, and a neighbor had an '81 Monte Carlo with a Turbo V6 and a stick. Check the Hollander Interchange Manual ( the "Bible" that junkyards use to know what parts interchange on what vehicles ) and see what you can find. Also-I would think the much more plentiful '82-92 Camaro / Firebird linkage would adapt to a "G" body pretty easily, as well as '64-77 "A" body stuff. If you just "Gotta Have" a 4 or 5-speed in your "G" body you can certainly do it-depending on the combo you want to run. If your putting a T5 behind a 305 or 350 Chevy-that's probably a snap-just find a wrecked stick-shift 305 '82-92 Camaro / Firebird and pirate everything. If your putting a Rock-Crusher behind a 454 Chevy or a 455 Olds or Pontiac-you may have to do some fabrication!!  It's possible-but it may not be cheap or easy.  I also had a couple people ask me about trans-planting fuel-injection systems. Again-you can do it, but it's going to be a major pain in the ass. If you "Gotta Have" a "Tuned Port Injected" small-block Chevy in your car I suggest going to a junkyard and finding an '85-91 Corvette, Camaro or T/A that has an L98 350 or LB9 305 in it, and get the whole engine, the wiring harness, the fuel pump, everything you can. If that's not possible, then get the induction system, the distributor, and the wiring harness. A company called Painless sells complete wiring harnesses to make this conversion easier. Edelbrock and Accel offer ported baseplates and runners, and BBK offers larger throttle bodies and higher flow per hr injectors. You can make these systems feed a 450 hp engine reliably; it just takes some time and effort. Ditto for Ford guys-find a wrecked "5.0" Mustang and get the whole engine if you can; other wise get the induction system and all the wiring. Painless offers wiring kits for this swap into other Ford bodies, and Edelbrock and Trick Flow and Ford SVT offer ported manifolds, larger throttle bodies, etc that can feed up to 400+ hp engines. Mopar guys-there are zillions of Dodge Trucks and Jeep Cherokees with 318 and 360 "Magnum" engines in them in junkyards. Get the whole shebang if you can, or at least the wiring harness, fuel pump, etc.  These system swaps work great when their done right; however a simple 4bbl carb and intake will make as much or more power, be dead reliable, and cost about 1/3 of the price and about 1/10th of the grief!!  Anyhow the path of LEAST resistance is still the way to go. As Jimmy the Greek once said-"The race may not always be to the swift, or the battle to the strong, but that's the way to bet".  Mastermind          

Sunday, December 30, 2018

Just because something is possible, doesn't mean you should attempt it....

I get people asking me all the time about wild combinations they read about in the buff magazines. Some are feasible, some are not. What kills me is the "Catch 22" of it. The people who are interested in these projects are not professional mechanics by trade, and have very little knowledge of cars in general. A professional mechanic would know not to attempt such a difficult endeavor. Here's an example. Some guy had read an article where a guy used a 350 Olds Diesel block ( they are much beefier than the gas models ) with a custom crank, Buick rods, custom pistons, etc that was bored and stroked to 440 inches. It also used 455 Olds heads, a custom ported Edelbrock RPM intake, a small-block Chevy type valvetrain etc. He wanted to know how much trouble it would be to duplicate this effort. More than it would be worth in both time and dollars I said. First off-if you want a big-inch Olds engine just buy a 425 or 455. They were used in virtually every model from 1965-76 and there is great aftermarket support. Secondly, rather than stroke out a 350-you could buy a 400-that was used from 1965-69, or you could use a 403. Even though they were only used from 1977-79-there are millions of them in Buick Rivieras, Park Avenues, and Electras, Olds 88s and 98s, Cutlasses and big BOP wagons, as well as Pontiac Bonnevilles and Catalinas, and Trans-Am and Formula Firebirds. Whether you hopped up a 403-which anything that fits a 350 Olds fits a 403-Edelbrock claims 397 hp on the 350 Performer RPM package-53 more cubes would definitely put you well over 400 hp, or the "old-school" 400-425-455-either one would be much cheaper and easier to build, and probably make as much or more power than a stroked out 350 diesel with a bunch of custom, expensive, one-off parts. Something isn't cooler just because it's hard to do. It's possible to put a 460 into a Fox Mustang, but why? I know guys that are running 10s and 11s with 302s or 347s ( 302 with a stroker crank ). Is a 460 swap going to go faster than that? Probably not, and we know it's going to cost way more, and be a ton of hassle to do. So why do it?  I touched on these before-but here's two more examples of people wanting to take the path of MOST resistance. The one guy was thinking of buying his neighbor's pristine, low-mileage '89 Mustang. It was a 4-banger model. He asked about swapping in a 302. I told him to just go buy a "5.0" Mustang. Their plentiful. Swapping a V8 into a 4-cylinder model would be a nightmare. The number of parts you'd have to chase down is staggering. Again-it's just easier-go buy a Mustang that has a 302 in it from the factory. I have seen rough-but-running examples as low as $1,200 and anything over $2,500 is usually pretty nice. Then he asks about turbocharging the 4-cylinder. Same deal-I told him to find an '84-86 SVO Mustang. These had Recaro seats,4-wheel disc brakes, upgraded suspension,50-series tires on 16" wheels and a Turbocharged 2.3 liter 4-cylinder engine with between 175 and 205 hp depending on years. Trying to turbo a stock 2.3 with aftermarket parts would be major-league expensive and probably wouldn't be as fast or reliable as a warmed-over "5.0".  The other guy had a '79 Trans-Am with a 403 Olds / TH350 powertrain. He asked how much trouble it would be to convert it to a 4-speed. Too much. I said. I recommended he sell the car and look for another 70's-era T/A or Formula Firebird with the 400 Pontiac / 4-speed combo from the factory. "No, really?" he asked. "No, really." I answered. Besides chasing down the clutch linkage and all the pedals, the shift linkage, the crossmember,the transmission, and the bellhousing, the main problem is GM never offered the 403 in any GM car with a manual transmission. Where is he going to get a flywheel? No one offers an aftermarket manual-trans flywheel for a 403!!  He could probably use a 350 Olds flywheel, but GM hasn't built a car with a 350 Olds engine and a manual transmission since 1974!!  Where are you going to find a usable, 45 year old flywheel?  I had a similar conversation with a guy who had an L98 350 / TH700R4 IROC-Z.  His buddy had an LB9 305 / 5-speed Z / 28. The IROC was faster in a drag race but the stick Z/28 was more fun to drive. He asked what it would take to convert the IROC to a 5-speed. I told him just sell the car and use the money to buy a nice LB9 or L69 / 5-speed Z/28 or T/A / Formula Firebird. I said putting an Edelbrock Performer Intake and matching cam on the carburated L69 would bring the hp up to or beyond the L98's.  For an LB9 model I suggested a 160 thermostat and a fan switch that turned the fan on at 185 instead of 220 would help immensely. I also suggested a larger throttle body, and Edelbrock's ported baseplate and TPI runners. These mods would bump the LB9's power level from 215 hp past the L98's 240 easily.  Yes the parts are readily available to do the change-over in junkyards or the aftermarket-but honestly-do you really want to chase down the trans, the bellhousing, the flywheel, the clutch, the linkage, the pedals, the shift linkage, cut a hole in the floor for the shifter, adapt a new neutral safety switch, etc, etc?  Wouldn't it be easier to just buy a car with a 5-speed already in it? Like I said minor, relatively inexpensive upgrades would bump the 305's power up to the 350's level.  In fact-if he just "HAD" to have a 350 / 5-speed combo-swapping a 350 for a 305 is an absolute bolt-in. Certainly a lot easier than swapping a TH700R4 for a T5!!   A couple of "G" body owners didn't like my suggestions either. One had an '84 Buick Regal. He wanted to swap in a 455 Buick. It's possible-I said. But since his car was powered by a 307 Olds V8, I said a 403 Olds would be a bolt-in swap. The nearly 100 extra cubes would certainly be an instant power and torque infusion, and that's if the 403 was bone-stock. If he used some headers and an Edelbrock intake and matching cam, he'd have a combo that would really rip on the street. The last 455 Buick rolled off the assembly line in 1976-43 years ago. Even if you find a running or rebuildable one-you have to chase all the tin and the brackets to mount the alternator, power steering pump, etc. The 403 would be so much easier and cheaper, and probably just as quick. The 2nd guy had an '85 Pontiac Gran Prix and wanted to convert it back to "real" Pontiac power. Since it had a 305 Chevy under the hood-the easiest path to big power would be to bolt in a 350 or 383 Chevy. Besides chasing down a 400 Pontiac-which have been out of production since 1977-and all the brackets,accesories, etc-since Chevy engines have a different bellhousing bolt-pattern than BOP engines, you'd also need a new transmission. And is a 400 Pontiac going to run any stronger than a well-built 350 or 383 Chevy?  No. The cost vs gain just doesn't add up. So think carefully before you take on some "easy" project. Yes manned space flight is possible-but it isn't cheap or easy!  Mastermind                      

Wednesday, December 26, 2018

The "Other" 350s re-visited.....

While the big-block cars get all the press and people fight with machetes to buy them, the fact remains that there are hundreds of thousands of  LeMans, Firebird, Ventura, Cutlass,Omega, and Skylark,and Regal models out there built from 1968-77 that have 350 cubes under the hood. If you have or want to buy one of these cars don't despair. If your buying one to swap a 455 into, then by all means do it; but if your not planning an engine swap these "other" i.e.-non-Chevrolet 350s can be made to run to pretty damn good. Good enough that you'll surprise some smug big-block owners in a drag race. # 1. 350 Olds. Out of the BOP ( Buick , Olds, Pontiac ) 350s the Olds engine has the most potential. The reasons are two-fold-one their a large-bore, short stroke design. Two-there was a factory high-performance version-the fire-breathing W31. Olds 350s respond well to basic hot rod tricks-4bbl carb and intake, headers and dual exhausts, cam upgrades. If you have a heavy car with an automatic-most '70's Cutlasses-you want to go for maximum torque. That means 1 5/8 headers and a dual-plane intake like the Edelbrock Performer. I'd also use the matching Performer cam. This simple combo will make more than 350 lbs of torque from idle on up which will give you some great street performance. I'd also change axle ratios. Most '70's Cutlasses had 2.56:1 or 2.73:1 gears which is not conducive to good acceleration. I switch to something in the 3.23:1-3.42:1 range. This will give you a huge boost in 0-60 and 1/4 mile acceleration without hurting drivability or freeway cruising rpm too much. If you want a wilder combination-dig for '68-72 heads. These have 70cc combustion chambers which will give you a full one point boost in compression over later 83cc heads. On '75 and later blocks you'll have to re-tap the bolt holes in the heads to change from 7/16 to 1/2 inch bolts. Not a big deal. I'd use the Edelbrock Performer RPM intake, or if you can find one-( they've been out of production for years ) a single-plane Holley Street Dominator. ( I had one on a 403 Olds T/A and it really woke it up ). The vaunted W31 had a cam with 308 ( 232@.050 ) duration and .474 lift. It was so lumpy that W31s were only available with a 4-speed and 3.90:1 or 4.33:1 gears, and couldn't be ordered with power brakes because the engine didn't make enough vacuum to operate them! This is because the Olds engineers took the cam out of the 400 /455 Ram Air engines. Plus you have to realize this cam is cut on 1966 profiles and is not computer optimized. If you "gotta have" it-and have a stick or an automatic with a 2,800 rpm converter and are using 3.73:1 or 4.10:1 gears-it will run like a scalded cat. But your giving up quite a bit of low-end and mid-range torque for top-end rush. The cam I like better is made by both Lunati and Edelbrock. It has 224 / 234 duration ( @.050 ) and .496 / 520 lift. You'll need some roller rockers and different pushrods but Harland Sharp has you covered, and Crane and Comp Cams also sell adjustable rockers for Olds engines. You'll still need a 2,500 rpm converter and 3.42:1 or 3.73:1 gears, but this cam makes 11 inches of vacuum at idle and has a lot more low and mid-range torque than the factory W31 cam, yet still pulls hard to 6,000 rpm and beyond. Edelbrock claims 397 hp and 400 lbs ft of torque with this combination. 400 hp will make any street car an absolute rocket. There are people who go wilder than this-using factory or Edelbrock 455 heads, custom domed pistons, and a custom ported intake, etc-but to them my question is this-If you need more than 400 hp and 400 lbs of torque, and have that much money, why aren't you building a 455 instead of a 350?  # 2. 350 Pontiac. 350 Pontiacs respond well to 4bbl carb and intake, headers and dual exhausts, mild cam,etc. I'd recommend either a factory '67-72 intake or an Edelbrock Performer or the old P4B if you run across one at a swap meet. For cams the Edelbrock Performer grind is great as is the factory "068" cam which Crane, Comp Cams, Lunati and others make exact replicas of. Again-most '70's LeMans, Firebirds and Venturas are going to have salt-flats gearing; swap the 2.56:1s for something in the 3.23:1-3.73:1 range for a stunning improvement in acceleration. These simple mods will give you 325-350 hp and 400 lbs of torque. You simply amplified what the factory did-made big torque at low rpm. If you need more than that then you need a 400 or 455, period. The limiting factor is the 350 is a small-bore design. The big-valve high-performance heads used on the 400 and 455 engines necessary for big power can't be used because the valves will hit the block. Some people will talk about releiving the block to clear the big heads, but why?  If you need that much power then just build a 400 or 455.  # 3. 350 Buick. The Buick is last for two reasons-one-unlike it's Pontiac and Olds cousins-there was never a factory high-performance version. Two-there is very little aftermarket support. Edelbrock doesn't even make a manifold for them, and they make manifolds for everything-including 472-500 Cadillacs, Flathead Fords, Hondas, LS motors, everything. There's just no parts available. There is one company called TA performance-don't ask me why-they don't make Pontiac parts-they do Buicks-and they offer aluminum intakes, cams, headers etc for 350 Buicks. You can make 290-340 hp and 375-400 lbs of torque pretty easily with parts from TA. Beyond that you'll need a 400-430-455-which Edelbrock, Crane, Comp Cams, Hooker, and many other companies DO make parts for!!  Hope this helps the owners of the "other" 350s out.  Mastermind            

Sunday, December 16, 2018

A "Pure Stock" Small-Block Chevy....

As promised in the previous post today we'll talk about building a small-block Chevy to run in the Pure Stock drags. There's only 3 displacements that you can run. ( Unless you have a '76 El Camino with a 400 ).  These will be 302, 327 and 350. These are all easily doable with a 350 block, as they all have the same 4.00 inch bore size. GMPP, Eagle, Lunati and other companies sell cranks with 3.00, 3.25 and 3.48 inch strokes to get your desired displacement. TRW sells the proper pistons. Every one has a list of "gotta haves" when talking about the SBC. 4-bolt mains, forged cranks, "Pink" rods, screw in studs, etc. Yes, if your building a NASCAR Nextel Cup racer that has to go 7,800 rpm for 500 miles at Daytona, you need all the beef you can get. For a street machine that only sees weekend trips to the drags, you don't need any of that stuff. Seriously. Two bolt main blocks are fine. Cast cranks are fine as long as rpms don't go over 7,000. I have seen guys run 2-bolt mains, cast cranks and cast pistons for 2 whole seasons in an IMCA race car without a rebuild or a single problem, and these roundy-round racers are far more abused than your car will be. As for rods-the stock rods are bulletproof, especially if rpms are kept under 6,500. Stock length is 5.7 inches. Many Nascar builders run 6.0 inch rods with custom pistons. You can do this if you want some extra torque in the mid-range, and your getting new pistons anyway. If your re-using the old pistons, then save the money for other parts that offer a bigger bang for the buck. # 2. Cylinder heads. There's three types of heads I recommend. The first is simply use the heads that came on the engine. Here's why. Some people diffentriate between "standard" and "Hi-performance" heads. Standard heads have 1.94 intake valves and 1.50 exhaust valves and pressed in rocker studs. Hi-perf heads have 2.02 / 1.60 valves and screw-in studs. But here's the kicker-both heads have the exact same size intake and exhaust ports. Any competent machine shop can install the larger valves in standard heads for a minimal fee, as well as screw-in studs if you want some extra beef.  Which you don't need. My friends and I have drag raced and circle-track raced Small-block Chevys for 40+ years and I have NEVER seen a stud pull out of a head.  The 2nd one is '81-86 305 "smog" heads. These have 1.84 intakes and 1.50 exhaust valves. However-their 58cc combustion chambers will bump compression on the average 350 from 8.2:1 to about 9.6:1 when replacing 76cc heads. The large boost in hp and torque from the extra compression will more than offset the slight loss of airflow from the smaller intake valve, or any machine shop can install 1.94 valves easily and cheaply. The third type is 1996-2003 "Vortec" heads. You can buy a set of brand-new Vortec heads from Scoggin-Dickey for $700. This is a screaming deal, because most machine shops would charge nearly that much to re-condition your old heads, and they probably couldn't duplicate the trick valve job that the GM factory puts on the new heads. Vortecs breathe better than other factory head and many aftermarket ones. Their 64cc combustion chambers will bump compression one full point over 76cc heads. All these features make this a 25-40 hp bolt-on. You will need a Vortec bolt pattern intake. GMPP offers a replica of the original Z/28 / LT-1 intake in cast iron in standard and Vortec bolt patterns. This manifold makes power from idle-7,200 rpm. It is almost impossible to out-power this manifold. It's also available in aluminum if your restoring a Z/28 or LT-1 'Vette or just building the motor to those specs. Stock class rules say the intake has to be the original "type"-which means either Iron or Aluminum depending on what model you have, or are claiming to clone. Carb choices are limited to two. If your doing a Z/28 / LT-1-you can use a #3310 780 cfm Holley.  Everything else will require a Quadrajet. Luckily-the GMPP manifold is a spread-bore bolt pattern and will accept either carb without need for an adapter. # 3. Cam. The cam I recommend for this application is the Comp Cams 270H Magnum. It has 224 / 224 duration ( @.050 ) and .470 lift. It will be a little lumpy in a 302, better in a 327, and really sweet in a 350. It pulls hard from idle-6.500 rpm. I'd only use it with a stick in a 302. With a 327 / 350 it will work with an automatic and a stock torque converter. However it will launch better if you have a 2,000-2,400 rpm converter. Crane, Comp Cams, and Lunati all offer exact replicas of the original Z/28 / LT-1 solid-lifter cam if you want to use it. However-the hydraulic Magnum cam works so well and is so maintenance-free that I don't think spending the time and money to switch to a solid-lifter design is worth the extra money or the time needed to constantly adjust valve lash settings. The other hydraulic design I recommend is sold by GMPP and Crane. It's an exact replica of the "350 hp" L46 / L82 cam. It has 222 duration (@.050 ) and .450 / .460 lift. It pulls hard from idle to 6,000 rpm and works great even with an automatic and a stock converter.     # 4. Exhaust. Since many circle-track classes require iron exhaust manifolds, there are several companies that offer ported and extrude-honed Iron manifolds for small-block Chevys. Most are ported reproductions of the classic "Ram's Horn" '60's 'Vette style-but they work almost as well as steel tube headers. Use at least 2 1 /4 inch pipes and low-restriction mufflers.  # 5. Gearing. Use 4.10:1 gears. This ratio will cover a 302's lack of low-end torque ( there's a reason '67-'69 Z/28's were only available with a 4-speed and 3.73:1 or 4.10:1 gears ) and get it moving with alarcity, and will give a 327 /350 some serious mid-range and top-end pull through 2nd,3rd and 4th. ( Or 2nd and 3rd if your running a TH350 ). Depending on car weight-obviously a Nova will be quicker than a Chevelle, or a 'Vette quicker than a Camaro-this combo should run very low 13s to mid-12s depending on traction and driver skill, and will cost very little to build, and will be bulletproof dependable.  Mastermind

Tuesday, December 11, 2018

More tips for building a Pure Stock champ....

I said in the last post that I'd go in depth on building a Pure Stock contender. Since every engine line is different we'll have to concentrate on a specific motor. I've always been a Pontiac guy so I'll use a Pontiac as an example. I have also built many Chevys, Fords, Mopars and Oldsmobiles over the years, and if folks want advice on those I can certainly do posts about those engine lines. Anyhow-I'll use the Pontiac as our test mule. Since the 400 was used in virtually every model from 1967-78 these will be the most plentiful and chances are whether your running a LeMans, GTO, Firebird, Trans-Am or Gran Prix, this is the engine your car came with anyway. # 1. Bottom end. Most stock class rules say the engine has to be within 15 cubic inches of stock. Since a 400 Pontiac is actually 401 inches, you can build a 416. Eagle, Butler, Kauffman and other places offer Pontiac cranks in nodular Iron, cast steel and forged steel. They also offer various stroke lengths as well. Since Pontiacs are not high-revvers-were going to accentuate what the factory did, which is make big hp and torque at low rpm. Even though were technically building a race car-were going to redline it at 6,200 rpm for reliability. At that redline a stock crank or a cast steel one will work just fine. Well use one with a 3.79 inch stroke. This is slightly longer than stock which is 3.75. This coupled with a .030 or .040 overbore will give you 412-415 inches. Stock Pontiac rods are 6.675 inches. Eagle sells 6.8 inch rods for Pontiacs and Ross and TRW sell pistons to work with the longer rods. The extra stroke and longer rods will boost torque all through the range. This is why small-block Chevy NASCAR racers have used 6 inch rods for years. ( Stock is 5.7 ). Use a stock-type ( TRW, Melling ) replacement oil pump. # 2. Heads. Pontiacs run best with flat-top pistons and high-compression heads. If you have a 1970 or earlier engine with 72cc combustion chambers, your all set. this will give you about 10:1 on a 400. 1971 and later engines have much larger combustion chambers which dropped the compression. Any other time I would say use the Excellent Edelbrock Performer RPM heads with 72cc chambers. Most stock classes don't allow aluminum heads, you have to use iron. If you can't find some early heads-#670, 46,48 etc. the next best thing is the "6X" "smog" heads used on 350s and 400s from 1976-79. These actually breathe better than any factory head except the vaunted 1969-70 RAIV and '71-72 455HO heads. Pontiac heads can be milled as much as .060 inch to raise compression. ( You have to shave the intake side as well so the manifold will fit properly ). Using milled 6X's and flat tops will give you about 9.7:1 compression, which will be enough, because Pontiacs love a lot of timing. # 3. Cam. Most stock classes only stipulate that the cam has to be the original "type". In other words if the car had a hydraulic cam stock, then you have to run a hydraulic cam, you can't switch to a solid-lifter cam or a roller. However there's no real limits on lift or duration. I like one that Crane makes. It has 232 / 242 duration ( @.050 ) and .473 / .488 lift. It's a hair hotter than the factory RAIV ( 231 /240 and .470 ). It works great with a stick. If your running an automatic I like the Edelbrock Torker Cam. It has 224 / 234 duration ( @.050 ) and .465 / 488 lift. The slightly less duration gives it a better idle and allows it to work with a stock torque converter. Pontiacs make so much bottom-end torque that if you use a torque converter with more than 2,500 rpm stall speed, you'll just blow the tires off.  Since Pontiac heads ( exceptions are Edelbrocks or RAIV's ) don't breathe much over about .480 lift-you don't need a .600 lift cam. With a Pontiac, less is more. Either of these cams will pull hard from idle-5,800-6,200 rpm, which should be your shift point anyway. # 4. Induction. Most stock classes say the intake has to be the original type. With this rule-you could say your building an RAIV spec car. ( RAIV's and 455HO's had aluminum high-rise intakes from the factory ). If they allow this-Ames, NPD and other companies offer reproduction aluminum RAIV intakes. If the rules say the intake has to be Iron, don't despair. Pontiac Iron intakes from 1967-74 are excellent. ( 1975 and later models have the EGR valve intruding into the throttle opening which limits power above 4,000 rpm ). The preferred ones are the '67-72 models. ( No EGR valve at all ). Port-matching to the gasket helps. Carb-wise-Summit, Jet and other companies offer street / strip and race Quadrajets.  If your building a '62-63 Super Duty Catalina Tribute-they may allow an Edelbrock or Offenhauser dual-quad aluminum intake. If so-I'd use two 750 Edelbrocks. ( And a 4.00 inch stroke crank with 3.00 inch mains to get 434 inches with a .030 overbore on a 400 block. You'll be legal-within 15 inches of the stock 421 ). If your running a tri-power setup I'd use a mechanical linkage instead of vacuum. # 5. Exhaust. There are several companies that make ported and extrude-honed iron exhaust manifolds for Pontiacs. Behind them I'd use 3 inch pipes and low-restriction mufflers. # 6. Gearing. I'd use 4.10:1 or 4.33:1 gears. These ratios will allow you to rip out of the hole,and pull hard through all the gears. It's funny with a big-block-in my 455 Hurst / Olds when I swapped the 3.23 gears for 4.10s-it didn't help one iota in low gear. However it made a HUGE difference in 2nd and 3rd!!  Since were redlined at 6,200 rpm this will be perfect. You'll be going through the traps at 5,700-6,000. 4.88:1s would make you go slower, because you'd run out of rpm before the end of the 1/4. Depending on traction-this simple combination should run very low 12s or very high 11s, which would make you super-competitive. Maybe we'll do a small-block Chevy next.  Mastermind  

Monday, December 10, 2018

Tips for building a Pure Stock champ....

Some of the buff magazines have coverage of the Pure Stock drags this month so I've gotten some inquirys from people wanting to know the best combination to run. There is no magic "winning" combination or formula. I can give you some advice on what to do to maximize your performance. If you already have a car your planning to run-then you have to tailor your modifications to that car's strengths and weaknesses. If your going to buy a car to run, you need to think carefully. For example if you want a big-block Chevelle what year should you run? From 1966-69 the largest engine was a 396. From 1970-72 you could get a 454. Ditto for a Pontiac GTO. Fom 1964-66 they had 389s. From 1967 on the 400 was standard equipment and the 455 became optional in 1970. So should run a '70 and later model to take advantage of the monster 454 Chevy and 455 Pontiac right? Maybe not. a 1964 GTO with a Tri-Power 389 is rated at 348 hp. Let's say it has a 4-speed and a 3.90:1 rear end. And a '64 GTO weighs about 3,400 lbs. A '70 GTO with a 455 is rated at 360 hp. And it weighs 4,070 lbs. Let's say it's an automatic with 3.23:1 gears. Or a 4-speed with 3.55:1s. ( 455 GTO's didn't have stiff gearing options in 1970; although rated at 360 hp; it was a "station wagon" engine. The vaunted 455HO which had RAIV heads and intake and exhaust coupled with the "068" cam didn't debut until 1971. The RAIII and RAIV 400s were considered the top performance options in 1970 and could be had with 3.90:1 or 4.33:1 gears ). Guess what? 12 hp won't overcome a nearly 700 lb weight advantage and the mechanical advantage of stiffer gearing. All other things being equal-the '64 GTO wins the drag race easily even though it's the car with "less" power. Ditto for the Chevelle owner-early Chevelles are much lighter than later ones; and the under-rated L78 375 hp 396 ( The L78 was intially rated at 425 hp in the 1965 Corvette. Later models in the Chevelle line were-down-rated for insurance purposes, but the engine was the same. )  had everything-heads, cam carb and intake that the mighty 450 hps LS6 454 had. Now if your a Ford Guy the shoe is on the other foot. A '72 Mustang has a 351C as the largest engine. A 1969 or 1970 model can use a 428.  We could go on for days with various examples but you get the idea. Anyhow here's some good tips that work, regardless of make or model. # 1. Always build the lightest car that you can. It's simple power-to-weight ratio. All other things being equal-a 3,000 lb car with a 300 hp engine will run just as fast as a 4,000 lb car with a 400 hp engine. However-a 300 hp engine is a lot easier and cheaper to build than a 400 hp one.  So build a Nova instead of a Chevelle. A Duster or Dart instead of a Charger or Road Runner. A Maverick instead of a Torino.  # 2. Always build the biggest engine you can afford. For example a 350 Chevy makes way more power and torque than a 305, yet costs no more to buy or build. In fact-since I have seen stroker rotating assemblys that have the crank, rods, pistons, rings and bearings and an oil pump as low as $399-it really doesn't cost any more to build a 383!  On the other hand if you have a good 400 Pontiac or 383 Chrysler or 396 / 402 Chevy-don't throw it away and then spend a mint buying and building a junk 440, or 454 or 455.  The key word is "afford." # 3. Don't forget mechanical advantage. The strongest engine in the world will be a dog if it's saddled with 2.56:1 gears. Run the gear that will give you the best 1/4 mile time. On a solid-lifter, high-winding 302 '69 Z/28-4.56:1s would rock. On a hydraulic cammed 350 hp 396 Chevelle-some 3.73:1s would be better-4.56:1s would cause it to run out of rpm before the end of the 1/4!!  # 4. Traction. All the power in the world doesn't do you any good if you can't put it to the ground. Excessive wheelspin loses more races than any other factor. Check your class rules; some allow traction bars or pinion snubbers, some don't. You can also play with tire size and tire pressure. Most classes allow sticky street tires like Mickey Thompson or M&H, some allow drag radials, some don't. Maybe next time we;ll talk  about a specificic car and how to really fine-tune everything. Mastermind      

Tuesday, December 4, 2018

Iron fists, velvet gloves revisited.....

I get a lot of people asking me how can they get serious power from their musclecar and look stock. It can be done, it just takes a little ingenuity. While individual engine lines have nuances that will vary-there are some things that will work across the board regardless of which kind of engine your building. I'll stick to those for this discussion. # 1. Increase displacement. The old saying "There's no substitute for cubic inches, except cubic dollars" is still true. All other things being equal, the larger engine will always make more hp and torque. In some cases it's a no-brainer engine swap-i.e.-swap your 305 Chevy for a 350, or your 307 Olds for a 350 or 403. In others a stroker crank / rotating assembly is the way to go. There are kits to turn a 350 Chevy into a 383, a 302 Ford into a 347, a 351W into a 392, a 360 Chrysler into a 408. That's just the small-blocks. There's kits to turn a 400 Pontiac into a 428 or 455,a 400 Mopar into a 451, a 440 into a 505. There's kits to turn 454 Chevys into a 496. Whether your combo is mild or wild, extra cubes mean extra power. #2. Camshaft. Since no one can possibly know what cam your running ( a lumpy idle will tell the practiced ear it's not stock ) a cam swap is a great "stealth" modification. Larger engines can tolerate more "cam" than smaller ones because usually your trading some bottom-end and mid-range torque for top-end rush. The larger engine having more torque to start with-won't notice the loss as much. For example if you have a 455 Pontiac that has 480 lbs of torque at 2,700 rpm-and your "hot" cam causes it to lose 30 lbs ft at low rpm-guess what? It still has 450 lbs of tire-boiling torque, and you won't notice the supposed "loss". You will notice the big "kick" from about 3,000 rpm on up however! Conversely if you had a late-'70's 350 Chevy that had 280 lbs of torque-and you dropped 30 lbs ft off-idle-you'd definitely notice that!  Manual transmission cars can also tolerate more "cam" than automatics because idle speed isn't as important and the driver can launch at whatever rpm he desires by manipulating the clutch. Using the small-block Chevy as an example-the old standby-the "350 hp 327 Corvette" cam. This cam would ruin a 305. It works pretty damn good in a 327 with a 4-speed and 3.73:1 gears, better in a 350 with 3.23:1s or stiffer either stick or automatic, provided you have a 2,000 rpm+ torque converter, and is really sweet in a 383 / 400 regardless of transmission or gearing. In a 400-this cam will rock even with an automatic, a stock converter and 3.08:1 gears. See what I'm saying?  Consult the cam manufacturer for your engine line. Obviously a cam that's considered "mild" in a 460 Ford would be horrible in a 302 or 351. One that's "super-hot" in a 318 Chrysler will purr like a kitten in a 440. Those are broad strokes-but you get the idea. With small-blocks and cars with automatic transmissions it's better to err on the side of caution.  # 3. Induction. Since stock-class drag racers and circle track racers deal with this-many classes require running a "stock" iron intake manifold, there are several companies that offer ported iron manifolds that will give you a gain of 25 hp and 30 lbs ft of torque. GMPP sells an exact replica of the original Z/28 / LT1 manifold that's good from idle to 7,200 rpm-in cast iron. Some engine lines-Pontiacs and big-block Mopars built prior to '75-have excellent manifolds from the factory. A little port matching to the gasket helps a lot. You can also use an Edelbrock or Holley or Weiand aluminum intake and paint it the factory color. This isn't as stealthy as the iron ones, but the casual observer won't notice. The other thing you can improve on is carburation. For example the Carter AVS that came on most 383 / 440 Mopars only flowed about 585 cfm. They had very crisp throttle response and a strong mid-range-a smaller carb will do that. But they were limited on the top-end. Think-a 440 V8 with a 585 cfm carb is like a 250 lb NFL running back trying to run while breathing through a straw. Fortunately Edelbrock has their excellent 800 cfm Thunder AVS models that would be just the ticket. Ditto for some other cars-pre-'67 Pontiacs and Chevys-early Fords,-many had Carter AFBs that flowed 500 or 625 cfm. Edelbrock's "Performer" line of carbs is an exact copy of the AFB with some modern improvements and are available in 500, 600 ( great for dual-quad applications ) 750 and 800 cfm version. I don't need to tell you that a 409 Chevy or 421 Pontiac will run much better with a 750 / 800 cfm carb than it will a 500 or a 625! The same goes for Holleys. Most concurs shows now allow carbs to be the original "type". Ok-get rid of the 50 year old 735 Holley on your 428CJ and replace with a 780 or an 850. Who's going to look at the casting numbers on your carb?  # 4. Exhaust. Here's where you have to make a big decision. A good set of headers and dual exhausts can be worth as much as 50-70 hp. Super Chevy did a test on a pristine LS6 Chevelle. With stock manifolds it pulled 380 hp on the dyno. ( A little off from the factory 450 hp rating; but back then pre-1972- gross ratings were done with no accessories. The lower net ratings used from 1972 on are more accurate. ) With headers it pulled 451 hp. A gain of 71 hp! And that was the first run. They hadn't yet adjusted the carb jetting to compensate for the opened up exhaust or played with ignition timing or distributor advance curve. With a little tuning they might have gotten an even bigger gain, but the point was made. Personally I would put headers on any car or truck I own where it's feasible. The gain in hp and torque, and usually a small bump-2-3 mpg in fuel economy is too good to pass up. But if you want the total "Stealth" "Stock" look-there are companies that sell ported and extrude-honed iron exhaust manifolds-again luckily for you-catering to the racing classes that require iron exhaust manifolds. Or any competent machine shop could do the ones off your engine. Even with iron manifolds-using 2 1/2 inch pipes, an X-pipe or balance tube and low-restriction mufflers can add as much as 30 hp. # 5. Mechanical advantage. Most '70's cars have salt-flats gearing like 2.73:1. Switching to something in the 3.23:1 to 3.73:1 range will give you a HUGE improvement in 0-60 and 1/4 mile time without hurting freeway cruising rpm or drivability too much. Most automatic cars can use a little more stall speed on the torque converter. Don't go crazy-chances are your engine isn't wild enough to warrant a 4,000 rpm converter and 4.56:1 gears-but a converter with 2,000-2,300 rpm stall speed will work wonders for most applications. # 6. Traction. Most musclecars-especially big-block cars can use larger than stock tires and could use some traction aids. A Pinion snubber is good for leaf-spring cars and Lakewood, Competition Engineering and other companies make bolt-on traction bars for leaf and coil-spring suspensions. You can see traction bars-but they help immensely. As for tires BFG, M&H, Mickey Thompson-all offer drag radials and sticky street tires that are DOT-legal. Hope this helps you "sleeper" builders out!  Mastermind                

Sunday, December 2, 2018

Some rare birds that can be bargains...

It's funny that some people want something unique, but then don't want to pay a premium price for it. I've had several people of late ask me to recommend some unique, cool musclecars that can be bought at reasonable or even cheap prices. Some of these will be cheap, some not, but they are all worth taking a look at if you want that model car. # 1. 1980 Z/28 Camaro. For this one year only you could get a 350 V8 backed by a T10 4-speed with a 3.44:1 1st gear and a 2.28:1 2nd, and a 3.08:1 positraction rear end. This combo had better acceleration and higher top speed and better gas mileage than the '77-79 models which had a 2.64:1 low gear, a 1.75:1 2nd and a 3.73:1 rear end. Automatics had a 3.42:1 rear axle which was a good compromise between jackrabbit starts and easy freeway cruising. This year also marked the return of "Cowl Induction" a vacuum operated hood scoop that opened under full-throttle acceleration and sounded cool. It also bumped power up 10 hp to 190 on the workhorse L48 350.  For some strange reason-for '81 if you wanted a 4-speed Z/28 you were stuck with a 305 that wheezed out 145 hp. You could still get a 350 with an automatic. And Canadian models still got the 350 / 4-speed combo. It wasn't emission laws-because in both 1980 and '81 you could still get a 350 / 4-speed combo in the Corvette. ( The 190 hp L48. The 230 hp L82 was only available with a TH350 ).  Dynamite if you can find one. # 2. 1982 Corvette. This one year only offered the C3 body that had been around since 1968 with the "Cross-Fire" Injected 350 and 4-speed automatic that was going to power the all-new '84 'Vette. They were decent performers for the time-15 second 1/4 mile times and 7 second 0-60 times. They make fun weekend cruisers and there is a million ways to build power into a small-block Chevy if you want more oomph. # 3. 1984 Corvette. These featured the all-new C4  with the "Cross-Fire" injected 350. Most had the TH700R4 4-speed automatic, but some had the "4+3" which was a T10 4-speed manual coupled with an electric overdrive that could be engaged in 2nd.3rd and 4th, effectively giving you 7 gears. It was a pretty trick setup that worked really well. 'Vette collectors snub these cars in favor of the '85-91 "Tuned Port Injected" models which keeps prices low. I have seen '84 models on used car lots as low as $2995. # 4. 1984-86 Ford Mustang SVO. These had Recaro seats, upgraded suspension, 50 series tires on 16" wheels, 4-wheel disc brakes, and a Turbocharged 4-cylinder engine that put out 175-205 hp depending on year. They didn't sell well when new because the "5.0" V8 models were both cheaper and faster. Their still a cool ride if you can find one, and prices have dropped considerably over the years. # 5. 1987-92 Lincoln MKVII LSC. Often called a "5.0" Mustang in a tuxedo, these featured Recaro seats, 4-wheel disc brakes, 16" wheels with 50 series tires, and the 225 hp 302 out of the Mustang GT backed by a 4-speed automatic and a 3.27:1 rear axle. Any speed parts that fit a Fox Mustang will fit these so there's a ton of potential.  #6. 1989 20th Anniversary Pontiac Trans-Am. These had the vaunted 3.8 liter Turbocharged V6 out of the now-defunct Buick Grand National. Grossly Under-rated at 250 hp and 355 lbs ft of torque, these were much quicker than the LB9 and L98 305 and 350 V8 models. And since the V6 was lighter than the V8s, the already stellar handling of the WS6 T/A was further improved. These bring a King's Ransom, but their worth it. I honestly don't know why Pontiac didn't make this the standard powertrain for the T/A. Probably because it would have ruined Corvette sales.  # 6. 1989-95 Ford Thunderbird SC. The "SC" stood for "Super Coupe" which is accurate. These cars had 4-wheel disc brakes, 50 series tires on 16" wheels, and a Supercharged 3.8 liter V6 that put out 210 -230 hp and 315-330 lbs of torque depending on year. 5-speed manual and 4-speed automatics were the transmissions. They were quick-6 second 0-60 times and 15 second 1/4s, with a 140 mph top speed. However-hot-rodders have made 400 hp reliably by turning up the boost and have run 11 second 1/4 mile times in the buff magazines. If you can't find one of these, from '91-95 the 302 out of the "5.0" Mustang was available, and their's speed parts galore for those. Dynamite if you can find one.  # 7. 2005-2009 Cadillac XLR-V. These were a racy, two-seat coupe based on the Corvette chassis and powered by a Supercharged 4.6 liter Northstar V8. They made a tire frying 443 hp and did 0-60 in 4.6 seconds and the 1/4 in 13 flat. Top speed was electronically limited to 155 mph. These are definitely Jules' wallet from "Pulp Fiction"-the one that says "Bad Mother$%er" on it.  The downside is they cost about 100 grand when they were new, so they won't be cheap. Now there not any more pricey than a same-year Corvette, but are much cooler if your willing to step up.  Like the Ferarri salesman told Nicolas Cage in "Gone in 60 seconds" if you were driving any one of these-"You wouldn't be an asshole sir, you'd be a conissuer".  Mastermind